Detailed Sealer Information
Trojan Masonry Sealer
(200 sq.ft./gal.)
PRODUCT DESCRIPTION: Trojan Masonry and Concrete Sealer is a penetrating water dispersed polyester polymer and polyurethane that when dry forms a monolithic barrier that fills the voids and completely solidifies the surface and interior particles of the concrete matrix thereby reducing moisture transmission.
TYPICAL USES: For industrial, commercial and residential use on concrete, brick, stucco and all masonry. For homes, sidewalks, driveways, basements, buildings, roads, tunnels, bridge decks, parking lot structures, hydroelectric dams, roof systems, subways and reservoirs. Use inside or outside on new or old masonry.
PRODUCT ADVANTAGES: Remarkably superior to other sealers because it seals and protects from within. As Trojan does not contain any solvents, it is non-toxic, non-flammable, non-caustic and has low VOC. Trojan penetrates into the concrete or masonry 2 - 4 inches and provides a paintable surface. Authorized by USDA for use in federally inspected meat and poultry farms. Ten Year Waterproofing Warranty.
ENVIRONMENTAL QUALIFICATIONS: Trojan Masonry Sealer provides LEED (Leadership in Energy and Environmental Design) credits toward LEED Certification for Green Building projects by promoting Indoor Environmental Quality (IEQ).
IEQ Credit 3 - Construction - Indoor Air Quality Management Plan
IEQ Credit 4 - Low Emitting Materials
QUALITY CONTROL TESTS: Trojan Masonry Sealer has passed nine independently performed quality tests per the American Society for Testing and Materials (ASTM), Australian Standard (AS) and NCHRP specifications. These tests include:
ASTM 413 - “Water Absorption of Chemical Resistant Concrete/Masonry” .Tested the effectiveness of Trojan Masonry Sealer in resisting water penetration. Trojan was applied in 1994 on one of Coca Cola Company’s major exposed concrete roof-top parking structures.
In 1997, three years after application, Coca Cola hired independent laboratory, H.C. Nutting Company to perform the ASTM 413 test. Test results revealed an “excellent” performance in the waterproofing ability of Trojan as it proved that there was no penetration of water from the core samples of the concrete deck.
ASTM C140 - “Masonry Absorption Test for Light Weight Block”. Trojan Masonry Sealer was applied to light weight block and weighed in its dry state. The block was then placed in water for 2 days. Afterwards it was weighed again while still wet. The 2-day test results are as follows:
Sample No. |
Dry Weight |
Wet Weight |
Percentage Absorption |
1 |
28.56 LBS. |
28.72 LBS. |
0.56% |
2 |
28.68 LBS. |
28.78 LBS. |
0.35% |
ASTM requires that water absorption cannot exceed 1% after 2 days of immersion. The results prove that Trojan Masonry Sealer far surpassed these requirements.
ASTM 123D - “Penetration Test for Nuclear Power Plant, 8000 psi Concrete Pour”. This test was performed by Pittsburgh, Plate and Glass subsidiary, Keeler & Long to determine the penetration of Trojan Masonry Sealer on a Nuclear Plant slab that was 8000 psi pour.
Six months after Trojan was applied, the ASTM-123D test was performed by taking two 2” core samples. After diamond sawing the cores in half, the test revealed that the Trojan penetrated 2 inches. As the normal pore for a concrete slab is 3000 to 4000 psi in density, Trojan can easily penetrate 2 to 4 inches on regular concrete.
Blue Dye Test - “Blue Dye Absorption Test”. Independent laboratory, H.C. Nutting Company conducted a Blue Dye Test for the Department of Public Works of Cincinnati, Ohio at the Garfield Garage parking deck. Trojan was applied to the concrete surface along with several other sealers. Afterwards, two 1” diameter cores approximately 2” long were extracted from each test site of the concrete parking deck. The objective of the test was to determine to what extent the blue dye was absorbed if any. Trojan was top rated as “excellent” at not allowing the blue dye to penetrate the concrete surface.
ASTM 642-82 - “Masonry Absorption Test for Brick”. Independent laboratory, H.C. Nutting Company coated a brick with Trojan Masonry Sealer and then submerged the test brick in water for 48 hours. The objective of the test was to determine water absorption of the brick by establishing its weight when dry before being submerged and again weighing the test brick immediately after its 48 hour water submersion. The results showed no weight increase of the brick after it was taken out of the water, thus proving that Trojan provided total waterproofing of the brick by not allowing water to be absorbed.
ASTM C672 - “Scaling Resistance”. Independent laboratory, H.C. Nutting Company completed the scaling resistance test on treated concrete after applying Trojan Masonry Sealer. Test results showed that there was no scaling after 100 weathering cycles (via mechanical brush) on the concrete that was sealed with Trojan as opposed to severe scaling on untreated samples of the concrete.
AS 1012.21-1999 - "Water Absorption of Hardened Concrete". Determination of water absorption and apparent volume of permeable voids in hardened concrete. Trojan Masonry Sealer passed this standard by not allowing water absorption.
NCHRP 244 – Cube Test – “Accelerated Weathering Test”. Trojan Masonry Sealer surpassed the standard of not exceeding 25% of untreated cube absorbed chloride.
NCHRP 244 – Southern Exposure – “Chloride Ion Penetration Test”. Trojan Masonry Sealer did not allow chloride penetration and thus passed absorbed chloride requirements not to exceed 10% of untreated concrete.
ADDITIONAL PRODUCT INFORMATION FOR TROJAN MASONRY SEALER (click here)
COLOR: Translucent. Dries clear with no gloss
PHYSICAL CONSTANTS:
* State: Liquid
* Vapor Pressure: (Air + 1) - N/A
* Solubility in Water: Dilutable
* Boiling Point: 100 degrees Celsius / 212 degrees Fahrenheit
* Freezing Point: 0 degrees Celsius / 32 degrees Fahrenheit Water
* Specific Gravity: (Water=1) - 1.10 @ 20 degrees Celsius
* Evaporation Rate: (BAC=1) - Same as Water
* Percent Solids by Weight: 13%
* pH: 6.8
* Volatile Organic Compounds: 11.67 G/L
APPLICATION:
Method: Spray on using low pressure sprayer
Theoretical Coverage: 200 square feet per gallon
Application Instructions: See Product Data Sheets (PDS)
SHIPPING & STORAGE
Container Type: 1 Gallon * 5 Gallon Pail * 55 Gallon Drum
Shipping Weight: 9.4 lbs. * 46 lbs. * 496 lbs.
Average Shelf Life: 12 months minimum from date of manufacture when maintained in protected storage. Storage at 40-90 degrees Fahrenheit
PRODUCT DATA SHEETS
View PDS
MATERIAL SAFETY DATA SHEETS
View MSDS
Trojan Ultra Masonry Sealer
(200 sq.ft./gal.)
PRODUCT DESCRIPTION: Trojan Ultra Masonry and Concrete Sealer has the same penetrating water dispersed polyester polymer and polyurethane that is incorporated in the Trojan Masonry Sealer. The difference is that we've added acrylic to the formala that settles on the surface to provide a low gloss sheen. When dry, Trojan Ultra forms a monolithic barrier that fills the voids and completely solidifies the surface and interior particles of the concrete matrix thereby reducing moisture transmission.
TYPICAL USES: For industrial, commercial and residential use on concrete, brick, stucco and all masonry. For homes, sidewalks, driveways, basements, buildings, roads, tunnels, bridge decks, parking lot structures, hydroelectric dams, roof systems, subways and reservoirs. Use inside or outside on new or old masonry.
PRODUCT ADVANTAGES: Remarkably superior to other sealers because it seals and protects from within. As Trojan Ultra does not contain any solvents, it is non-toxic, non-flammable, non-caustic and has low VOC. Trojan Ultra penetrates into the concrete or masonry 2 - 4 inches and provides a low gloss finish. Ten Year Waterproofing Warranty.
COLOR: Milky in container. Dries with a clear low gloss, satin finish
PHYSICAL CONSTANTS:
* State: Liquid
* Vapor Pressure: (Air + 1) - N/A
* Solubility in Water: Dilutable
* Boiling Point: 100 degrees Celsius / 212 degrees Fahrenheit
* Freezing Point: 0 degrees Celsius / 32 degrees Fahrenheit Water
* Specific Gravity: (Water=1) - 1.10 @ 20 degrees Celsius
* Evaporation Rate: (BAC=1) - Same as Water
* Percent Solids by Weight: 19%
* pH: 6.8
* Volatile Organic Compounds: 52.79 G/L
APPLICATION:
Method: Spray on using low pressure sprayer
Theoretical Coverage: 200 square feet per gallon
Application Instructions: See Product Data Sheets (PDS)
SHIPPING & STORAGE
Container Type: 1 Gallon * 5 Gallon Pail * 55 Gallon Drum
Shipping Weight: 9.4 lbs. * 46 lbs. * 496 lbs.
Average Shelf Life: 12 months minimum from date of manufacture when maintained in protected storage. Storage at 40-90 degrees Fahrenheit
PRODUCT DATA SHEETS
View PDS
MATERIAL SAFETY DATA SHEETS
View MSDS
Trojan Color Sealer
(First Coat - 200 sq.ft./gal., Second Coat - 300 sq.ft./gal.)
PRODUCT DESCRIPTION: The same penetrating polyester formula as our Trojan Ultra and Trojan Masonry Sealers yet also includes our specially formulated dye system and still comes with a Ten Year Waterproofing Warranty.
TYPICAL USES: For industrial, commercial, and residential use. Can be applied to any porous substrate including concrete, masonry and brick or concrete pavers.
PRODUCT ADVANTAGES: This product is not a paint that will easily wear away over time, as once sprayed on, it will penetrate the surface and provide a dye stain that is absorbed into the surface. The benefit is that we have combined our waterproofing Trojan Masonry Sealer and UV resistant dyes into one product. Trojan Color Sealer is an environmentally safe alternative to toxic acid stains.
FINISH/COLOR: Satin or Flat Finish. Thirty Six Colors.
NOTE: The left side of each digital picture has one coat of Trojan Color Sealer applied. The right side has two coats applied for a darker appearance.
EARTH TONES |
TROPICAL COLORS |
 |
 |
For a Larger View, please click on the below links:
« Earth Tones Color Chart » « Tropical Colors Color Chart »
Special Note: These colors are representational only. The actual color may be more transparent as different textures and colors of concrete will accept the pigments differently. It is strongly advised to test this product in an out-of-the-way area to see how your concrete will accept the color e.g. very porous concrete will absorb more pigment whereas very smooth, hard concrete will absorb less. Any of these colors may be made more transparent by adding plain Trojan Masonry Sealer.
In order to ensure adequate waterproofing, either two coats of Trojan Color Sealer should be applied or if the more transparent color of one coat is desired then one coat of Trojan Color Sealer should be followed by a second coat of Trojan Masonry Sealer (which is clear). Coverage of 1st coat is 200 sq.ft./gallon. Coverage of 2nd coat is 300 sq.ft./gallon.
Allow new concrete to dry 30-60 days before applying Trojan Color Sealer. It is recommended that our non-toxic, pH Reducer be applied to new concrete under 12 months old as a pretreatment before applying Trojan Color Sealer. As new concrete is naturally caustic (high pH) it can attack any sealant, dye or coating system. Therefore we have created a liquid applied pH Reducer to help decrease pH levels. Ideal pH levels should be in the 5 to 10 pH range.
Untreated Concrete |
Concrete with Trojan Color Sealer |
 |
 |
PHYSICAL CONSTANTS:
* Appearance: Colored liquid (various)
* State: Liquid
* Solubility in Water: Infinite
* Boiling Point: 100 degrees Celsius / 212 degrees Fahrenheit
* Freezing Point: 0 degrees Celsius / 32 degrees Fahrenheit Water
* Specific Gravity: (Water=1) - 1.10
* Evaporation Rate: (BAC=1) - Same as Water
* Percent Solids by Weight:19% - 21% (Varies by color)
* pH: 6.8
* Volatile Organic Compounds: 52.79 G/L
APPLICATION:
Method: Spray or Roll
Theoretical Coverage: 200 square feet per gallon
Application Instructions: See Product Data Sheets (PDS)
SHIPPING & STORAGE
Container Type: 1 Gallon * 5 Gallon Pail * 55 Gallon Drum
Shipping Weight: 9.4 lbs. * 46 lbs. * 496 lbs.
Average Shelf Life: 12 months minimum from date of manufacture when maintained in protected storage. Storage at 40-90 degrees Fahrenheit
PRODUCT DATA SHEETS
View PDS
MATERIAL SAFETY DATA SHEETS
View MSDS
Trojan Beta-Z Wood Sealer
(200 sq.ft./gal.)
PRODUCT DESCRIPTION: A unique water-based polyester and acrylic formula manufactured for the effective and safe treatment for the preservation of all wood surfaces. This sealer is intended to be used before the application of paint or other top coats. This sealer effectively holds finish coats of paint on the surface thereby requiring less material.
TYPICAL USES: For industrial, commercial, and residential use. A one of a kind product for home owners, general contractors, waterproofing contractors, paper mills, lumber yards and government agencies.
PRODUCT ADVANTAGES: is the most effective wood sealer on the market because unlike most top coat sealers, the Trojan Beta-Z actually penetrates the fibers of the wood thereby providing superior protection. It is non-flammable, non-caustic and non-toxic. Will not harm aquatic life.
COLOR: Translucent
PHYSICAL CONSTANTS:
* State: Liquid
* Vapor Pressure: (Air + 1) - N/A
* Solubility in Water: Dilutable
* Boiling Point: 100 degrees Celsius / 212 degrees Fahrenheit
* Freezing Point: 0 degrees Celsius / 32 degrees Fahrenheit Water
* Specific Gravity: (Water=1) - 1.10 @ 20 degrees Celsius
* Evaporation Rate: (BAC=1) - Same as Water
* Percent Solids by Weight: 19%
* pH: 6.8
* Volatile Organic Compounds: 52.79 G/L
APPLICATION:
Method: Brush, Roll or Spray
Theoretical Coverage: 200 square feet per gallon
Application Instructions: See Product Data Sheets (PDS)
SHIPPING & STORAGE
Container Type: 1 Gallon * 5 Gallon Pail * 55 Gallon Drum
Shipping Weight: 9.4 lbs. * 46 lbs. * 496 lbs.
Average Shelf Life: 12 months minimum from date of manufacture when maintained in protected storage. Storage at 40-90 degrees Fahrenheit
PRODUCT DATA SHEETS
View PDS
MATERIAL SAFETY DATA SHEETS
View MSDS